Harley Davidson Low Rider Drivetrain & Transmission Tools

Universal Air Regulator by Feuling®. Air Regulator, 1/8 NPT gauge fitting, 1/4 NPT air inlet and outlet. Air Regulator fits tool #9010. If you"re looking for a quality product that will serve you for years to come, look no further.

Universal Lifter Pump Up Tool by Feuling®. Transmission fluid to pump oil into the lifter side feed hole to push all of the air out of the lifter internals. You will see air bubbles come out the top pushrod seat hole, Its best to work...

Universal Tool Kit by Helix Racing®. This top-grade product is expertly made in compliance with stringent industry standards to offer a fusion of a well-balanced design and high level of craftsmanship. Manufactured from industry-leading...

5-Speed Door Puller by JIMS®. Use to remove Big Twin 5-Speed transmission door. This tool easily removes the transmission door, with gears and shafts attached and without any scratches or frustrations. Puller will not damage door bearing.

6-Speed Main Drive Gear Bearing and Seal Installer Tool by JIMS®. Use this tool to safely install new main drive gear bearings and seal. This tool will hold bearings and seal square to it's bore, eliminating any marring of the bearings...

6-Speed Transmission Door Remover Tool by JIMS®. Use this tool to remove (pull) the complete door with gears and shafts from the transmission. No longer will you need to remove the trap door by prying or hitting with a hammer. Just...

Bearing and Race Puller Tool by JIMS®. This tool has been designed to remove the flywheel sprocket shaft inner bearing race with the supplied JIMS® T-bar and hardware. If heat is needed to remove race see tool No. 899.

Cam Bearing Tool by JIMS®. Use to install inner cam bearing, with Handle No. 33416- 80 on right (Handle slips through the outer cam bushing for alignment). All of JIMS® bearing installers are designed with an angle to apply all the...

Cam Seal Installer and Remover Tool by JIMS®. Use to install and remove a 1970-1999 cam seal without removing the cam cover. This tool is very simple to use. Just mount tool in cover, screw in the two removing screws, turn center, and...

Clutch Assembly Service Tool by JIMS®. This tool will safely disassemble and assemble the clutch shell assembly. Easily removes and installs the clutch hub from it's bearing. Safely removes and installs the clutch shell ball bearing...

Cruise Drive Vise Stand by JIMS®. Faster, easier, and safer assembly is now possible. To assist in the assembly of the transmission gears and shafts, JIMS® has developed the Cruise Drive Vise Stand. No more fumbling with parts on the...

Universal Hardware Organizer Complete Kit by JIMS®. Tired of hunting through plastic bins looking for hardware? The patent pending JIMS Hardware Organizers will guarantee all hardware is organized during powertrain teardown, storage,...

Inner Cam Bearing Installation Tool by JIMS®. This tool easily presses the inner cam bearing smoothly into the right case, with the cases assembled, to the proper depth. Use a new JIMS performance bearing No.9058 and to remove old use...

Main Bearing Installer Tool by JIMS®. Use this tool to safely install a new main bearing using hand tools. This job can be performed with the transmission still in the frame. Tool will hold bearing square to it's bore, eliminating any...

Main Case Seal Installer by JIMS®. H-D's new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings made. These main case bearings are of such high precision that you must be very gentle when...

Main Drive Gear Bushing Tool by JIMS®. Use to remove and install the main drive gear bushings, also to remove Big Twin cam bushing 1970- present. If you're looking for a quality product that will serve you for years to come, look no...

Main Drive Gear Installer Tool by JIMS®. Use this tool to safely install a new or newly repaired main drive gear. This job can be performed with the transmission still in the frame, with hand tools. This tool will hold the main drive...

Main Drive Gear Remover Tool by JIMS®. This tool removes the main drive gear from the main bearing correctly while in the transmission case. This eliminates the need of an arbor press and the risk of case damage.

Main Drive Gear Seal Installer by JIMS®. This tool is designed to properly align and install to the right depth, the main drive gear seal, H-D® No.12077 into the end of the gear. This can be performed while the assembled transmission...

Mainshaft Sprocket/Pulley Locknut Socket by JIMS®. Heavy-Duty thick wall tube. Extra long two piece design, inner collar will retain wrench to nut for safer service work. 1-7/8" hex, 1/2" Drive. If you're looking for a quality product...

Motor Sprocket Shaft Seal Install Tool by JIMS®. Use to press oil seal over sprocket shaft into case. Use with No.97225-55. If you're looking for a quality product that will serve you for years to come, look no further.

Universal Race and Bearing Install Tool Handle by JIMS®. This top-grade product is expertly made in compliance with stringent industry standards to offer a fusion of a well-balanced design and high level of craftsmanship. Manufactured...

Saddlebag Latch Rivet Tool by JIMS®. This new more affordable JIMS hand tool is for used to install rivets used on the H-D OEM Fiberglass Saddlebags and Tour Paks latch mechanism pieces. If you're looking for a quality product that will...

Shifter Mechanism Sleeve Remover and Installer Tool by JIMS®. This is a real time saver for removing and installing the shifter mechanism sleeve in Cruise Drive Big Twin transmissions. With this new tool, the sleeve (bushing) can be...

Sprocket Locker by JIMS®. Use to lock final drive sprocket, for removing and installing sprocket nut. Use with JIMS® tool No.94660-37A. If you're looking for a quality product that will serve you for years to come, look no further.

Steering Head Bearing Race Installer by JIMS®. Use to install steering head races, stock and custom, as well as install cups in the frame. This tool pulls the races and cups in, straight and true, without any damage.

Steering Head Bearing Race Remover Tool by JIMS®. Use to remove and install steering head bearing race. Use with JIMS® spacer No.2388 and JIMS® Tool Handle No.33416-80 below. If you're looking for a quality product that will serve you...

Timken™ Bearing Or Race Installer Adapter Kit by JIMS®. This tool will upgrade your earlier JIMS® bearing installer tool to work on the latest fine spline Twin Cam® sprocket shafts. This tool is designed to install either H-D®...

Timken™ Bearing Race Installer by JIMS®. Use to install bearing races in left crankcase. Use this precision tool to press in bearing races straight time after time (a must for the later engine case). For removal of Big Twin races, in...

Timken™ Bearing Simulator by JIMS®. This tool is designed to allow quick and easy removal and replacement, of flywheel assembly in the left side crankcase when checking rod to case, piston to flywheel, or cylinder to flywheel...