JIMS Motorcycle Tools

Ignition Switch Alignment Key by JIMS®. This tool will easily align the ignition switch housing as the retaining screws are being torqued. This gives the ignition switch knob the alignment it needs to help extend the life of the...

Cam Bearing Puller Tool by JIMS®. Use to remove inner cam bearing without splitting cases. Easily pulls bearing from case, also keeps rollers from coming out during removal. Install a new JIMS No.9057 performance bearing using JIMS...

Connecting Rod Bushing Tool by JIMS®. Use to remove and replace wrist pin bushings without removing connecting rods from crankcases. Use JIMS® No.1284 Rod Holder tool. If you're looking for a quality product that will serve you for...

Crank Sprocket Lock Tool by JIMS®. This precision tool allows the technician to lock the camshaft and crankshaft sprockets to properly remove, replace and torque the sprocket bolts. This tool is made from non-marring Delrio.

Engine Stand by JIMS®. Top-quality steel bench stand simplifies engine overhaul and has powder coated finish. If you're looking for a quality product that will serve you for years to come, look no further.

Rolling Buddy Rubber Mounted by JIMS®. Rubber mounted Harley-Davidson® V-twins use the engine as a structural part of the chassis. When the engine is removed, it becomes impossible to roll the motorcycle. This can incapacitate a...

Valve Spring Compressor Tool by JIMS®. This tool is necessary for removing or installing valves. Hardened ball bearing style tip at valve head end eliminates damage to valve. Comes with new valve collar receiver for safer tool usage,...

Wrist Pin Bushing Reamer Tool by JIMS®. Use this kit to ream your wrist pin bushings to H-D® specifications. These reamers are made to exact tolerances, piloted to locate from the I.D. of your newly replaced JIMS® wrist pin...

Fork Dust and Seal Installer Tool by JIMS®. This tool is designed to install the lower leg 49 mm fork seal squarely into the bore without damaging the seal lip surface. Two piece design. If you're looking for a quality product that...

Fork Seal Slider by JIMS®. Use to install fork seals, dust seals and chrome caps. Lightly grease to keep from scratching fork tubes. If you're looking for a quality product that will serve you for years to come, look no further.

Universal Inline Spark Tester by JIMS®. This tool is designed to give you quick easy visual check of the ignition system. Quickly diagnose a ignition system with this in line tester. Works on all ignition systems including...

Inner Cam Bearing Remover Tool by JIMS®. Designed like JIMS popular EVO cam bearing tool, it removes the bearing easily without any damage to the crankcase. This precision built tool will also keep the pin rollers from accidentally...

Inner Primary Bearing and Seal Removal/Installation Kit by JIMS®. When it comes to servicing the inner primary bearing and seal, do it the JIMS way. This American made tool has a lifetime warranty and drives the bearing and seal...

Main Drive Gear Seal Installer by JIMS®. This tool is designed to properly align and install to the right depth, the main drive gear seal, H-D® No.12077 into the end of the gear. This can be performed while the assembled...

Mainshaft Bearing Race Tool by JIMS®. Use to remove and install the bearing inner race on the transmission mainshaft. If you're looking for a quality product that will serve you for years to come, look no further.

Master Cylinder Bleeding Solution Brake Lid Kit by JIMS®. At last there is now a hydraulic brake bleeding system where seeing is believing. A cleaner way to purge the system of air with less fluid used and a reduced chance of cosmetic...

O2 Sensor Thread Chaser by JIMS®. Use to remove any I.D. thread damaged from either exhaust carbon or the mating components, both in aluminum or steel. If you're looking for a quality product that will serve you for years to come, look...

Primary Locking Bar by JIMS®. Use to lock primary for service work. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy use which makes it the perfect deal for your ultimate...

Sprocket Shaft Bearing Installation Tool by JIMS®. Use to install flywheel assembly into left crankcase Timken® bearing. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy use...

Timken™ Replacement Sleeve by JIMS®. This bearing insert kit is designed exclusively for use with JIMS® tool No.959 shown above and must be installed only with this tool. The insert is made from aero space quality steel and has...

Transmission Case Shifter Shaft Seal Installer by JIMS®. Developed in conjunction with Hiro Koiso, one of JIMS sponsored Bonneville racers, these two simple tools make installing the shifter shaft seal precise and effortless. They...

Twin Cam™ Timken™ Case Bearing Conversion Tool by JIMS®. Order Timken® bearings separately. When increasing to a larger bore size and stroke, JIMS highly recommends for 2003 to present Twin Cam models you convert the left...

Universal Wheel Bearing Puller by JIMS®. This top-grade product is expertly made in compliance with stringent industry standards to offer a fusion of a well-balanced design and high level of craftsmanship. Manufactured from...

Balancer Shaft Alignment Tool by JIMS®. This tool is a must have for maintaining a long life of your balancer's drive chains and bearings. This tool will take all the guess work out of setting up your sprocket and chain alignment on a B...

Balancer Shaft Retention Pin by JIMS®. Use this tool to secure the engine balancers on Twin Cam B engines when servicing the flywheel assembly. This tool locks into the balancer's sprocket pin holes to prevent the balancer from turning...

Beta Case Support Block Tool by JIMS®. Derek Beck on JIMS "JIMS Tool Submission Program". This innovative tool is designed to protect the left engine case while servicing the inner balancer bearings or performing other general engine...

Cam Assembly Tool by JIMS®. Use to hold both cams in an upright position while lowering the cam support plate over both guides and cam journal guides. This tool has been manufactured from a non-marring material that will not damage any...

Cam Bearing Puller Tool by JIMS®. Use to remove inner cam bearing without splitting cases. Easily pulls bearing from case, also keeps rollers from coming out during removal. Install a new JIMS No.9057 performance bearing using JIMS tool...

Cam Bearing and Bushing Alignment Tool by JIMS®. Use to check the alignment of cam bearing to cam cover bushing to well within .0003" of centerline. Any binding of this tool indicates misalignment of cam cover, and or bushing. A must...

Cam Seal Installer and Remover Tool by JIMS®. Use to install and remove a 1970-1999 cam seal without removing the cam cover. This tool is very simple to use. Just mount tool in cover, screw in the two removing screws, turn center, and...