Harley Davidson Electra Glide Sport Drivetrain & Transmission Tools

Bearing and Race Puller Tool by JIMS®. This tool has been designed to remove the flywheel sprocket shaft inner bearing race with the supplied JIMS® T-bar and hardware. If heat is needed to remove race see tool No. 899.

Cam Bearing Tool by JIMS®. Use to install inner cam bearing, with Handle No. 33416- 80 on right (Handle slips through the outer cam bushing for alignment). All of JIMS® bearing installers are designed with an angle to apply all the...

Cam Seal Installer and Remover Tool by JIMS®. Use to install and remove a 1970-1999 cam seal without removing the cam cover. This tool is very simple to use. Just mount tool in cover, screw in the two removing screws, turn center, and...

Clevebloc Bushing Assembly Remover/Installer Tool by JIMS®. Use to remove and replace swing arm cleveblocs. Cleveblocs, part No.47556-81, are silicone filled bushings that will be damaged if not installed properly. JIMS® tool presses...

Clevebloc Spreading Tool by JIMS®. Use to install the swing arm in a 5-Speed rubber mount frame. When cleveblocs are replaced they need to be positioned to install in the rear of the transmission. This tool will spread the swing arm...

Clutch Assembly Service Tool by JIMS®. This tool will safely disassemble and assemble the clutch shell assembly. Easily removes and installs the clutch hub from it's bearing. Safely removes and installs the clutch shell ball bearing...

Clutch Hub Puller by JIMS®. Use to remove wet and dry clutch hub without removing clutch release rod. 4 bolts included for dry clutch removal. If you're looking for a quality product that will serve you for years to come, look no further.

Universal Hardware Organizer Complete Kit by JIMS®. Tired of hunting through plastic bins looking for hardware? The patent pending JIMS Hardware Organizers will guarantee all hardware is organized during powertrain teardown, storage,...

Inner Cam Bearing Installation Tool by JIMS®. This tool easily presses the inner cam bearing smoothly into the right case, with the cases assembled, to the proper depth. Use a new JIMS performance bearing No.9058 and to remove old use...

Main Drive Gear Bushing Tool by JIMS®. Use to remove and install the main drive gear bushings, also to remove Big Twin cam bushing 1970- present. If you're looking for a quality product that will serve you for years to come, look no...

Main Drive Gear Tool by JIMS®. Use to remove and install the main drive gear. Also installs the main bearing without removing transmission case. If you're looking for a quality product that will serve you for years to come, look no...

Mainshaft Sprocket/Pulley Locknut Socket by JIMS®. Heavy-Duty thick wall tube. Extra long two piece design, inner collar will retain wrench to nut for safer service work. 1-7/8" hex, 1/2" Drive. If you're looking for a quality product...

Motor Sprocket Shaft Seal Install Tool by JIMS®. Use to press oil seal over sprocket shaft into case. Use with No.97225-55. If you're looking for a quality product that will serve you for years to come, look no further.

Universal Race and Bearing Install Tool Handle by JIMS®. This top-grade product is expertly made in compliance with stringent industry standards to offer a fusion of a well-balanced design and high level of craftsmanship. Manufactured...

Saddlebag Latch Rivet Tool by JIMS®. This new more affordable JIMS hand tool is for used to install rivets used on the H-D OEM Fiberglass Saddlebags and Tour Paks latch mechanism pieces. If you're looking for a quality product that will...

Sprocket Locker by JIMS®. Use to lock final drive sprocket, for removing and installing sprocket nut. Use with JIMS® tool No.94660-37A. If you're looking for a quality product that will serve you for years to come, look no further.

Steering Head Bearing Race Installer by JIMS®. Use to install steering head races, stock and custom, as well as install cups in the frame. This tool pulls the races and cups in, straight and true, without any damage.

Steering Head Bearing Race Remover Tool by JIMS®. Use to remove and install steering head bearing race. Use with JIMS® spacer No.2388 and JIMS® Tool Handle No.33416-80 below. If you're looking for a quality product that will serve you...

Timken™ Bearing Race Installer by JIMS®. Use to install bearing races in left crankcase. Use this precision tool to press in bearing races straight time after time (a must for the later engine case). For removal of Big Twin races, in...

Timken™ Bearing Simulator by JIMS®. This tool is designed to allow quick and easy removal and replacement, of flywheel assembly in the left side crankcase when checking rod to case, piston to flywheel, or cylinder to flywheel...

Universal Tool Driver Spacer by JIMS®. The effectiveness of any bearing race remover tool is dependent on the ability to grip the race. This spacer applies outward force on the bearing race tool to grip better, allowing easier removal...

Transmission Case Shifter Shaft Seal Installer by JIMS®. Developed in conjunction with Hiro Koiso, one of JIMS sponsored Bonneville racers, these two simple tools make installing the shifter shaft seal precise and effortless. They...

Transmission Main Drive Gear Bearing Tool by JIMS®. Use to install main bearing H-D No.8905 or No.8906 to the factory depth. If you're looking for a quality product that will serve you for years to come, look no further.

Universal Chain Breaker by JOES Racing®. Universal Chain Breaker by JOES Racing®. #520. JOES Chain Breaker is specially designed to install your chain fast. Precision machining creates a strong tool that allows you to remove and...

Seal Installation Protector (20-20639) by Kibblewhite®. The flexible thin wall protectors are designed to fit over the top of the valve stem, protecting the sealing element from any sharp edges that might damage it during installation.

Seal Installation Protector (20-20636) by Kibblewhite®. The flexible thin wall protectors are designed to fit over the top of the valve stem, protecting the sealing element from any sharp edges that might damage it during installation.

Seal Installation Protector (20-20634) by Kibblewhite®. The flexible thin wall protectors are designed to fit over the top of the valve stem, protecting the sealing element from any sharp edges that might damage it during installation.

Seal Installation Protector (20-20637) by Kibblewhite®. The flexible thin wall protectors are designed to fit over the top of the valve stem, protecting the sealing element from any sharp edges that might damage it during installation.

Seal Installation Tool (20-20833) by Kibblewhite®. These installation tools for OE style seals are manufactured from high strength 6061-T6 Aluminum for increased durability when compared to plastic installers. The tools are designed for...

Seal Installation Tool (20-20831) by Kibblewhite®. These installation tools for OE style seals are manufactured from high strength 6061-T6 Aluminum for increased durability when compared to plastic installers. The tools are designed for...