Harley Davidson Street Glide Drivetrain & Transmission Tools

Universal Tool Kit by Helix Racing®. This top-grade product is expertly made in compliance with stringent industry standards to offer a fusion of a well-balanced design and high level of craftsmanship. Manufactured from industry-leading...

3rd Hand Axle Locker Tool by JIMS®. Have you noticed, as you are torquing down the axle nut after you set the proper belt tension, (Deflection) that the welded axle nut will move to the low side of adjuster cam? This movement will allow...

5-Speed Door Puller by JIMS®. Use to remove Big Twin 5-Speed transmission door. This tool easily removes the transmission door, with gears and shafts attached and without any scratches or frustrations. Puller will not damage door bearing.

6-Speed Main Drive Gear Bearing and Seal Installer Tool by JIMS®. Use this tool to safely install new main drive gear bearings and seal. This tool will hold bearings and seal square to it's bore, eliminating any marring of the bearings...

6-Speed Transmission Door Remover Tool by JIMS®. Use this tool to remove (pull) the complete door with gears and shafts from the transmission. No longer will you need to remove the trap door by prying or hitting with a hammer. Just...

Balancer Scissor Gear Alignment Screw by JIMS®. This tool holds the two halves of the spring before removal for easy installation. No more fumbling with screwdrivers while trying to align the gear in place. This screw is brightly...

Bearing and Race Puller Tool by JIMS®. This tool has been designed to remove the flywheel sprocket shaft inner bearing race with the supplied JIMS® T-bar and hardware. If heat is needed to remove race see tool No. 899.

Cam Bearing Puller by JIMS®. Once the camshafts are removed from the support plate this specialty tool will remove the bearing from the camshaft. Unlike a general purpose puller this tool was designed to remove the bearing straight with...

Cam Chain Tensioner Tool by JIMS®. This tool will unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams. This tool also checks spring loads on chain tensioners.

Clutch Assembly Service Tool by JIMS®. This tool will safely disassemble and assemble the clutch shell assembly. Easily removes and installs the clutch hub from it's bearing. Safely removes and installs the clutch shell ball bearing...

Connecting Rod Bushing Tool by JIMS®. Use to remove and replace wrist pin bushings without removing connecting rods from crankcases. Use JIMS® No.1284 Rod Holder tool. If you're looking for a quality product that will serve you for...

Countershaft 1st Scissor Gear Alignment Tool by JIMS®. This tool is essential for installation of the countershaft 1st scissor gear in Milwaukee Eight™ / Cruise Drive transmissions. It is installed before the scissor gear is removed...

Cruise Drive Vise Stand by JIMS®. Faster, easier, and safer assembly is now possible. To assist in the assembly of the transmission gears and shafts, JIMS® has developed the Cruise Drive Vise Stand. No more fumbling with parts on the...

Universal Hardware Organizer Complete Kit by JIMS®. Tired of hunting through plastic bins looking for hardware? The patent pending JIMS Hardware Organizers will guarantee all hardware is organized during powertrain teardown, storage,...

Main Bearing Installer Tool by JIMS®. Use this tool to safely install a new main bearing using hand tools. This job can be performed with the transmission still in the frame. Tool will hold bearing square to it's bore, eliminating any...

Main Bearing Remover and Installer by JIMS®. The Milwaukee Eight™ engine uses a completely unique engine case main bearing. With this in mind, JIMS® is proud to introduce a main bearing remover and installer designed just for the...

Main Case Seal Installer by JIMS®. H-D's new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings made. These main case bearings are of such high precision that you must be very gentle when...

Main Drive Gear Installer Tool by JIMS®. Use this tool to safely install a new or newly repaired main drive gear. This job can be performed with the transmission still in the frame, with hand tools. This tool will hold the main drive...

Main Drive Gear Remover Tool by JIMS®. This tool removes the main drive gear from the main bearing correctly while in the transmission case. This eliminates the need of an arbor press and the risk of case damage.

Main Drive Gear Seal Installer by JIMS®. This tool is designed to properly align and install to the right depth, the main drive gear seal, H-D® No.12077 into the end of the gear. This can be performed while the assembled transmission...

Main Drive Gear Tool by JIMS®. Use to remove and install the main drive gear. Also installs the main bearing without removing transmission case. If you're looking for a quality product that will serve you for years to come, look no...

Mainshaft Bearing Race Tool by JIMS®. Use to remove and install the bearing inner race on the transmission mainshaft. If you're looking for a quality product that will serve you for years to come, look no further.

Mainshaft Sprocket/Pulley Locknut Socket by JIMS®. Heavy-Duty thick wall tube. Extra long two piece design, inner collar will retain wrench to nut for safer service work. 1-7/8" hex, 1/2" Drive. If you're looking for a quality product...

Motor Sprocket Shaft Seal Install Tool by JIMS®. Use to press oil seal over sprocket shaft into case. Use with No.97225-55. If you're looking for a quality product that will serve you for years to come, look no further.

Neck Bearing Tool by JIMS®. Including Tri Glide® trikes. A new frame design change in the steering head & neck bearings for Harley-Davidson® motorcycles necessitates a new installation tool. Pounding the races into place is simply not...

Universal Race and Bearing Install Tool Handle by JIMS®. This top-grade product is expertly made in compliance with stringent industry standards to offer a fusion of a well-balanced design and high level of craftsmanship. Manufactured...

Saddlebag Latch Rivet Tool by JIMS®. This new more affordable JIMS hand tool is for used to install rivets used on the H-D OEM Fiberglass Saddlebags and Tour Paks latch mechanism pieces. If you're looking for a quality product that will...

Shifter Mechanism Sleeve Remover and Installer Tool by JIMS®. This is a real time saver for removing and installing the shifter mechanism sleeve in Cruise Drive Big Twin transmissions. With this new tool, the sleeve (bushing) can be...

Sprocket Locker by JIMS®. Use to lock final drive sprocket, for removing and installing sprocket nut. Use with JIMS® tool No.94660-37A. If you're looking for a quality product that will serve you for years to come, look no further.

Sprocket Shaft Seal Installation Tool by JIMS®. This top-grade product is expertly made in compliance with stringent industry standards to offer a fusion of a well-balanced design and high level of craftsmanship. Manufactured from...